For decades, the answer to every wort problem was “boil it harder”. Then research delivered an uncomfortable truth: evaporation rate barely controls DMS at all — temperature and pH do. So if a gentler boil strips DMS just as well, why are you still evaporating 8% of your wort? Let’s walk through the novel wort boiling technologies that cut thermal load, remove DMS deliberately and return the heat to your brewhouse.
DMS (dimethyl sulfide) is the benchmark volatile of wort boiling: how your kettle handles DMS-P (its precursor) is a good proxy for how it handles every other unwanted volatile. Classical kettles burn enormous energy to evaporate water — only to discover that DMS-P decomposition follows temperature and pH, not the evaporation meter. That single insight unlocks an entire generation of low-evaporation, energy-recovering boiling systems.
Why doesn’t more evaporation automatically mean less DMS?
In the traditional wort boil, the water evaporation rate runs almost parallel to the DMS-P decomposition rate — which means boiling intensity and evaporation volume have hardly any influence on how much DMS-P actually decomposes. Research shows the factors that really drive DMS release are temperature and pH. What does the free-DMS curve actually look through a conventional boil?

That is exactly why the novel technologies exist: once you accept that a gentler boil can still strip DMS, you gain a powerful lever to cut boiling intensity and evaporation volume — and save enormous amounts of energy without sacrificing the DMS target.
What are the four goals of novel wort boiling technology?
Every novel boiling system — vacuum degassing, steam stripping, Merlin, low-pressure evaporation — is built around the same four targets:

Which concrete measures cut the thermal load first?
- Raise wort pump capacity — the shorter the wort stands in the kettle, the lower its thermal load.
- Enlarge plate heat exchanger capacity so the hot-wort transfer and whirlpool stand stay below 45 minutes.
- Pre-cool during transfer: cast wort is cooled on its way to the whirlpool down to 70–85 °C.
- Separate breaks twice: after the whirlpool, a high-flow disc separator removes hot and cold break once more.
How does the vacuum degassing system work?
The vacuum degassing system treats the wort the moment boiling ends. The hot wort first enters a negative-pressure venting vessel topped by a condenser: flash evaporation under vacuum strips volatile substances — DMS among them — while the vapor is condensed and its heat fully recovered. The degassed wort then passes through a heat storage tank into the whirlpool, and from there everything proceeds traditionally. The effect: lower boiling intensity, less evaporation, major energy savings and lower production cost.

What is steam stripping — and why does a packed column do the job?
Steam stripping (desorption) tackles volatiles after the boil. The wort first runs through a clarifier and a pre-run tank, then is pumped to the top of a stripping column and sprayed evenly over the packing. Why packing? Because contact area is everything: depending on the packing type, one cubic metre of packing offers 50–500 m² of surface. Low-pressure steam is injected at the column bottom and rises against the falling wort film, evaporating the undesirable volatiles out of the wort. The stripped vapor is condensed — and the condensate leaves as 85 °C hot water stored in a buffer tank for process use. Nothing is wasted.

What does the stripping process look like phase by phase?
The stripping workflow treats boiling as three disciplined phases instead of one long rolling boil:
- Phase A — boiling. Bring the wort to 100 °C and hold a short, vigorous boil with gentle agitation: coagulation substances form and hop additions disperse evenly.
- Phase B — isomerisation hold. Keep the wort at 100 °C for as long as the α-acid isomerisation of your hop schedule requires.
- Phase C — volatile strip. A final short hold of just 5–10 minutes drives off gathered volatiles — with kettle evaporation not exceeding 1%.
Only then comes clarification, stripping, and wort cooling — where the stripped wort reaches the fermenter with DMS below 30 µg/L. And because the evaporation load is so low, the heat recovered from the condenser side can cut the process energy demand dramatically — savings of up to 92% are reported for the concept.
What do the numbers say — traditional vs modern boiling?
Put side by side, the operating figures tell the story clearly:
Table 1. Traditional vs modern wort boiling — key parameters (compiled from the source comparison, simplified)
| المعلمة |
Traditional boiling |
Modern boiling |
| Minimum boiling time |
60 min |
50–60 min |
| Total evaporation |
6–7 % |
variable — much lower with stripping |
| Iso-α-acid (isomerisation) rate |
50–60 % |
60–65 % |
| Hot wort pump-out from kettle |
15 min |
< 10 min |
| Coagulable nitrogen (12 °P) |
15–20 mg/L |
20–28 mg/L |
| Colour increase |
< 1 EBC |
< 1 EBC |
| Thermal load (TBA value) |
< 35 |
< 35 |
| DMS at the fermenter inlet |
higher, evaporation-dependent |
< 30 µg/L by design |
Read the table twice: modern systems hold or improve every quality marker — isomerisation, colour, thermal load — while cutting evaporation and pump-out time. That combination, not any single number, is the business case.
How does the Merlin boiling system work?
The Merlin system replaces part of the flat heater area with a conical heating surface — typically divided into a one-third and a two-thirds zone. Wort flows as a film over the cone, gaining excellent heat transfer with a small heating area, and the vapor generated is put to work: it is led into a vapor preheater and energy saver, where it condenses and heats process water to about 96 °C — water that then preheats incoming wort. The result is a boil that is shorter, cooler on the wort, and dramatically cheaper.

What does Merlin deliver in practice?
- Boiling time of only 35–40 minutes — so the thermal load, measured as the TBA (thiobarbituric acid) value, drops clearly.
- Evaporation of just 1.8% during boiling plus on average 1.5% during degassing — a total of only 4.1–4.5%, versus roughly 8% for a conventional boil.
- Dual use: combined with the degassing unit, the Merlin kettle can also serve as an external boiling device — which shortens total boil time further, while its heat-recovery behaviour stays intact.
- Beer quality: compared with other boiling systems, foam is finer and more persistent, the palate is milder, and hop aroma is more pronounced.
- Colour: brightness shifts only marginally — differences of about 2–3 EBC versus conventional boils.
Can low-pressure boiling with vacuum evaporation really halve energy use?
The Kasper Schulz principle combines gentle low-pressure boiling with a vacuum evaporator, so the total evaporation stays at a full 8% — without the usual energy bill:
- The wort boils in the kettle at about 100 °C for roughly 60 minutes with stirring, forming coagulable nitrogen in the 20–28 mg/L band.
- Hot trub separates in the whirlpool.
- A vacuum evaporator at 0.03 MPa strips the remaining 7% at a wort temperature of only 63 °C — cool enough to protect colour and aroma.
- The second vapor’s condenser heats process water; stripped heat returns as hot water at about 60 °C.
- Total boiling intensity — kettle plus whirlpool stand — remains 8%, so DMS and evaporation targets are met without compromis

What does the system promise on paper — and in the glass?
- First (primary) energy use cut by more than 50% versus a conventional brewhouse boil.
- Brewhouse yield is preserved — lauter and whirlpool performance are unaffected.
- Process water heats itself: the second-vapor condenser delivers hot water at about 60 °C; brewing water can be warmed to 60 °C in the plate heat exchanger on its way in.
- Beer quality does not drift: brewhouse comparisons show the beer analyses essentially identical, and taste panel plus forced-aging shelf-life tests revealed no differences.
Where does the brewhouse energy actually go?
Energy balances from a working brewhouse (per 225 hL of cast wort) put total brewhouse heat demand at roughly 3,249 kWh — split into about 46% for evaporation and 54% for wort heating, plus around 10% losses. In other words: even a perfect burner cannot escape the fact that more than half the heat goes into simply warming wort and vessels. That is why heat recovery matters more than burner size:
- Condensing the second vapor returns most of the evaporation heat as hot process water — utilization of the evaporation heat can reach around 77% with a well-dimensioned condenser circuit.
- Beyond roughly 5.5% evaporation, vapor-compression heat recovery becomes the decisive lever for further savings.
- Merlin-type systems flip the ratio: their heating demand concentrates on the wort-side (heating the cone and preheater circuit), which is exactly where recovered heat can be re-injected.
Design rule of thumb: first strip what you can strip gently (vacuum, low temperature), then recover what you have boiled (condensers, energy storage). A kettle that only evaporates is a kettle that throws money at the sky.
Frequently asked questions about novel wort boiling technologies
If evaporation rate doesn’t control DMS, what actually does?
Temperature and pH. DMS-P decomposes as a function of thermal history, and free DMS is stripped by contact between wort and vapor phase — both of which vacuum degassing and steam stripping deliver deliberately, without evaporating litres of wort for show.
What is the difference between vacuum degassing and steam stripping?
Vacuum degassing flashes the hot wort into a negative-pressure vessel immediately after the boil — fast, gentle, and integrated into the transfer path. Steam stripping runs the clarified wort through a packed column against low-pressure steam — more thorough contact, and it produces 85 °C hot water as a by-product.
Does a lower evaporation rate hurt flavour stability?
No — it helps. Thermal load, tracked as the TBA value, falls because the wort spends less time at high temperature. Lower thermal load means less oxidation, lighter colour and better flavour stability; modern systems hold TBA below the same limits as traditional boils.
How much energy can each novel system save?
Vacuum degassing concepts report savings up to 92% on process energy via condensate heat recovery; the Schulz low-pressure plus vacuum evaporation route cuts primary energy by more than half at a full 8% total evaporation; Merlin cuts total evaporation to 4.1–4.5% and recycles its vapor into ≈96 °C preheat water.
Can one kettle serve two roles?
Yes. A Merlin kettle combined with a degassing unit can operate as an external boiling device as well — shortening total boil time while keeping its heat-recovery behaviour intact. Dual-use equipment is one of the quiet economics of novel boiling.
Why is the whirlpool stand time capped at 45 minutes?
Every minute of standing adds thermal load without doing useful work. With a stronger wort pump and a larger plate heat exchanger, the transfer and stand sequence completes in under 45 minutes — protecting both the TBA value and the next brew’s schedule.
Does vacuum evaporation change the beer?
Comparative trials say no: beer analyses from the Schulz low-pressure/vacuum route match conventional brewing, and taste panels plus forced-aging tests showed no differences — while foam, palate and hop aroma actually improved with Merlin-type operation.
At what evaporation rate does vapor compression start to pay off?
Above roughly 5.5% evaporation, the recoverable second-vapor heat becomes large enough for compression-based heat recovery to be worthwhile. Below that, simple condenser heat recovery into process water usually delivers the better return.
Conclusion: boil deliberately, not brutally
The lesson of novel wort boiling is simple and uncomfortable: brute-force evaporation was never the point. DMS obeys temperature and pH; thermal load obeys time; and your energy bill obeys every litre you boil away for no reason. Vacuum degassing, steam stripping, the Merlin conical kettle and low-pressure vacuum evaporation each attack a different part of that waste — and all of them hand the recovered heat back to the brewhouse. Which of the four goals — lower intensity, stripped DMS, reduced TBA, protected foam proteins — is your current kettle failing first? That answer tells you exactly which system to look at.